standing seam metal roof attachment to insulation

STANDING SEAM METAL ROOF ATTACHMENT TO INSULATION INSTALL
STANDING SEAM METAL ROOF ATTACHMENT TO INSULATION SERIES

The ice and water shield must be installed over the top of the lock strip at the eaves. However, for your standing seam metal roof, your underlayment will be a self-adhering, high heat ice and water shield.

Underlayment is usually a felt (15 lb, 30 lb, or synthetic) material used over your decking to provide additional protection. Once the lock strips are put on the rakes and eaves, your underlayment will be installed. Your lock strips will be made out of the same color and gauge as your metal panels. The lock strips will be installed at the eaves (bottom edge of your roof) and rakes (the slanting edge of your roof).

Lock strips are what hold (lock) your standing seam metal panels to your roof edges and keep them from flapping in the wind or strong storms.

STANDING SEAM METAL ROOF ATTACHMENT TO INSULATION INSTALL

Install lock strips at the rakes and eavesĪfter your old roof is torn off, the starter lock strips are ready to be installed. To learn more about what this looks like, read this article on what a roof tear off is and how a contractor does it. The tear-off process is crucial to the replacement process. While one crew is going from section to section tearing off, another crew is making sure the torn off materials end up in the dump trailer or the tarped landing zone in your yard. Starting on the end furthest away from the dump trailer, they’ll start using special tear-off forks to tear-off your old roof by sections. What this means is that your roofing contractor will go section by section removing old roofing materials and tearing off your old shingles from the roof’s decking. Tear off your old roofīefore your new metal roof can be installed, your old roofing materials need to be torn off to get to a clean deck. Continue reading to learn the 6-step process to install your standing seam metal roof system 1. Now that you know what materials make up your new metal roof, you’re ready to learn how these materials come together to form a standing seam metal roof. 6-step process to install your standing seam metal roof To go more in-depth into these crucial components, read this article on what materials make up a standing seam metal roof.

Ridge capping: The trim installed at the peak where the two slopes of a roof meet.

Z bar: A piece of metal flashing bent in the shape of a Z that is 1/8th of an inch taller than the ribs on your metal panels.

Clips: Unseen fasteners that hold each panel to the roof deck.

However, you can get a different size gauge and multiple colors to choose from. Usually, the panels are made of 24 gauge pre-finished steel with a Kynar 500 finish (painted finish that protects the steel panels and keeps the color from fading).

Metal panels: The metal panels are what you see and what makes up the bulk of your standing seam metal roof.

For your standing seam metal roof, your underlayment will be a self-adhering, high heat ice and water shield.

Underlayment: Underlayment is usually a felt (15 lb, 30 lb, or synthetic) material used over your decking to provide additional protection.

Starter lock strip: Lock strips are what hold (lock) your standing seam metal panels to your roof edges and keep them from flapping in the wind or strong storms.

Roof decking: The wooden boards that make up the framing of your roof.

Your standing seam metal roof system is made up of the following components: But your standing seam metal roof system is made up of more than just the metal panels you see. Standing seam panels are fastened under each of these ribs to allow the panels to glide back and forth when your roof expands and contracts. The ribs (standing seams) are usually between 12 and 24 inches apart, depending on the length of the metal panel and aesthetics of the structure.

STANDING SEAM METAL ROOF ATTACHMENT TO INSULATION SERIES

What materials make up a standing seam metal roof system?Ī standing seam metal roof system is a series of metal panels that are locked together at the seams or seamed mechanically. Before we get to how it's installed, you need to know a little bit about this type metal roof system. So, how is a standing seam metal roof installed? Always eager to educate, I’m going to answer that question.īy the end of this article, you'll know the the 6 steps to install a standing seam metal roof. When you work with us, you’ll never worry about your roof again. We know what it takes to make your standing seam metal roof last for decades. The team at Bill Ragan Roofing has provided the residents of Nashville with high-quality metal roofs since 1990. If so, you need to know the process it takes for your roofing contractor to install your new standing seam metal roof. Are you ready for a new roof? Did you decide that you want a metal roof over the standard asphalt roof?

Standing seam metal roof attachment to insulation